Concrete plaster

Name: Concrete plaster
SKU: 826
Availability: InStock

Price range: $38.95 through $99.95

Surface: All surfaces: (Walls, counter, shower, floor, furniture, fireplace*)
Coverage: 70 sq. ft. / 2 coats (140 sq. ft. total)
Pot life: 5h to 6h Close the boiler between uses
Drying time between coats: 1h to 2h (accelerate with a fan)
Number of layers: 2 layers
Tools required: Boiler of minimum 7 liters, mixer on drill, stick for scraping walls, smoother or trowel, sandpaper 120, 180, (350)
Time before proceeding to the other step: 12h to 24h (next day)

Interior/Exterior

IMPORTANT: THE 3 KG OF COATING MUST BE PREPARED IN COMPLETE TO CERTIFY THE COLOR *

Art Béton Concrete Coating is real concrete that adheres to all surfaces. It is designed to be applied in 2 thin layers of 1 to 2mm each. Pay particular attention to the edges, apply an additional thickness to avoid crossing the concrete during sanding.

Square feet

Couleurs

Clear

- +

SKU: N/A Categories: Products, Step 2 - Concrete Coating

SURFACE PREPARATION

On new gypsum، pull them as if painting، on mdf or other material، joined with grid fiberglass tape. Apply the Art Béton Primer to the entire surface to be covered. Allow to dry until a translucent film is obtained before applying the Concrete Coating.
On ceramic or any uneven surface, apply PRE-STEP 1 Leveler.

CONCRETE COATING PREPARATION

Empty the Concrete Plaster into a suitable boiler of 7 liters or more. Add the necessary water. Mix with a mixer to obtain a homogeneous paste. Scrape sides well while stirring. Make sure to obtain a perfectly homogeneous mixture and that all the pigments are dissolved.
*** Once mixed, the concrete hardens in less than 3 hours in the boiler ***.

APPLICATION OF CONCRETE COATING

Apply a thin layer about 1 mm thick with a trowel or trowel. Make half-moons in all directions with the trowel. Gaps will be filled in the 2nd layer. Soften the raw edges with the spatula. Let dry until pale (about 2 hours, speed up drying with a fan). Apply a 2nd coat with the trowel by making half-moons, texture if desired. A 3rd coat can be applied if needed.

FINISHING

Wait until the next day in order to have optimal drying, sand the surface with 120 grit sandpaper to soften the edges and then with 180 grit paper. For a very smooth finish, use 320 paper. Proceed with sealing the concrete following the instructions in steps 3 and 4.
CLEANING: Clean the instruments with water while the concrete is still fresh.

OTHER COLORS ON SPECIAL ORDER

WARRANTY

- Les Enduits Art Béton offers a guarantee for its Art Béton coating system. The warranty is applicable for one year from the date of purchase of the system. Les Enduits Art Béton undertakes to replace the products used if, and only if, the application is made in strict accordance with the attached specifications and on a perfectly stable basis.
- Shelf life: 1 year after purchase
- Protect products from freezing at all times

*ARTBÉTON COATING IS NON-FLAMABLE. FOR USE ON A FIREPLACE DECOR WALL, IT MUST BE APPLIED OVER FIBER CEMENT OR ANY OTHER NON-FLAMABLE MATERIAL.

COMPLETE INSTALLATION GUIDE (PDF)

PRICE PER SQUARE FOOT FOR PROJECT

YOU ARE AT STEP 2!

STEP 1 – PRIMER STEP 3 – SEALANTS

Square feet

25-35 square feet, 50-70 square feet

Couleurs

White, CHARTREUX, TITANE, MULOT, FLANELLE, ARONIA, TOFFEE, EUROPEAN BEIGE, Ash Gray 4, Ash Gray 8, Ash Gray 24, Ash Gray 48, Ash Gray 72, Pure Gray 4, Pure Gray 12, Pure Gray 24, Pure Gray 48, Pure Gray 64, Taupe-Brown 10, Taupe-Brown 30, Taupe-Brown 70, Taupe-Brown 190, Taupe-Brown 230-75, Sand SO005, Sand SO012, Sand SO042, Yellow JC016, Yellow JC068, Yellow JC200, Turquoise-TC012, Turquoise TC044, Turquoise TC076, Blue BP024, Blue BP048, Blue BP200, Red RN042, Red RN080, Red RN100, Red RN200+25